View LK006R656_6749354.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

61 ?2008 littelfuse, inc. revised: july 9, 2008 teccor ? brand thyristors speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. lxx06xx & qxx06xx & qxx06xhx series 6 amp sensitive, standard & alternistor (high commutation) triacs 6.0a triacs lxx06xx & qxx06xx & qxx06xhx series description 6 amp bi-directional solid state switch series is designed for ac switching and phase control applications such as motor speed and temperature modulation controls, lighting controls, and static switching relays. sensitive type devices guarantee gate control in quadrants i & iv needed for digital control circuitry. standard type devices normally operate in quadrants i & iii triggered from ac line. alternistor type devices only operate in quadrants i, ii, & iii and are used in circuits requiring high dv/dt capability. features & bene?ts t 3p)4dpnqmjbou t (mbttoqbttjwbufe junctions t 7pmubhfdbqbcjmjuzvq to 1000 v t 4vshfdbqbcjmjuzvq to 85 a t &mfdusjdbmmzjtpmbufe l - package is ul recognized for 2500vrms t 4pmjetubuftxjudijoh eliminates arcing or contact bounce that create voltage transients t /pdpoubdutupxfbspvu from reaction of switching events t 3ftusjdufe psmjnjufe
3'* generation, depending on activation point of sine wave t 3frvjsftpomzbtnbmmhbuf activation pulse in each half-cycle main features symbol value unit i t(rms) 6a v drm /v rrm 400 to 1000 v i gt (q1) 5 to 50 ma schematic symbol mt2 mt1 g agency approval agency agency file number ? l package: e71639 absolute maximum ratings sensitive triac (4 quadrants) symbol parameter value unit i t(rms) rms on-state current (full sine wave) lxx06ly t c = 80c 6a lxx06vy / lxx06dy/ lxx06ry t c = 85c i tsm non repetitive surge peak on-state current (full cycle, t j initial = 25c) f = 50 hz t = 20 ms 50 a f = 60 hz t = 16.7 ms 60 i 2 ti 2 t value for fusing t p = 8.3 ms 15 a 2 s di/dt critical rate of rise of on-state current i g = 50ma with 0.1s rise time f = 120 hz t j = 110c 70 a/s i gtm peak gate trigger current t p c 10 s t j = 110c 1. 6 a p g(av) average gate power dissipation t j = 110c 0.4 w t stg storage temperature range -40 to 150 c t j operating junction temperature range -40 to 110 c note: xx = voltage, y = sensitivity applications excellent for ac switching and phase control applications such as heating, lighting, and motor speed controls. typical applications are ac solid-state switches, light dimmers, power tools, home/brown goods and white goods appliances. alternistor triacs (no snubber required) are used in applications with extremely inductive loads requiring highest commutation performance. internally constructed isolated packages are offered for ease of heat sinking with highest isolation voltage. ?
62 revised: july 9, 2008 ?2008 littelfuse, inc. teccor ? brand thyristors speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. speci?cations are subject to change without notice. please refer to http://www.littelfuse.com/series/triac.html for current information. 6 amp sensitive, standard & alternistor (high commutation) triacs lxx06xx & qxx06xx & qxx06xhx series absolute maximum ratings standard triac symbol parameter value unit i t(rms) rms on-state current (full sine wave) qxx06ry / qxx06ny t c = 95c 6a qxx06ly t c = 90c i tsm non repetitive surge peak on-state current (full cycle, t j initial = 25c) f = 50 hz t = 20 ms 65 a f = 60 hz t = 16.7 ms 80 i 2 ti 2 t value for fusing t p = 8.3 ms 26.5 a 2 s di/dt critical rate of rise of on-state current i g = 200ma with 0.1s rise time f = 120 hz t j = 125c 70 a/s i gtm peak gate trigger current t p c 10 s; i gt c i gtm t j = 125c 1. 6 a p g(av) average gate power dissipation t j = 125c 0.5 w t stg storage temperature range -40 to 150 c t j operating junction temperature range -40 to 125 c note: xx = voltage, y = sensitivity absolute maximum ratings alternistor triac (3 quadrants) symbol parameter value unit i t(rms) rms on-state current (full sine wave) qxx06lhy t c = 95c 6a qxx06rhy / qxx06nhy qxx06vhy / qxx06dhy t c = 100c i tsm non repetitive surge peak on-state current (full cycle, t j initial = 25c) f = 50 hz t = 20 ms qxx06vhy qxx06dhy 55 a qxx06lhy qxx06rhy qxx06nhy 80 f = 60 hz t = 16.7 ms qxx06vhy qxx06dhy 65 qxx06lhy qxx06rhy qxx06nhy 85 i 2 ti 2 t value for fusing t p = 8.3 ms qxx06vhy qxx06dhy 17.5 a 2 s qxx06lhy qxx06rhy qxx06nhy 30 di/dt critical rate of rise of on-state current f = 120 hz t j = 125c 70 a/s i gtm peak gate trigger current t p c 10 s; i gt c i gtm t j = 125c 1. 6 a p g(av) average gate power dissipation t j = 125c 0.5 w t stg storage temperature range -40 to 150 c t j operating junction temperature range -40 to 125 c note: xx = voltage, y = sensitivity
63 ?2008 littelfuse, inc. revised: july 9, 2008 teccor ? brand thyristors speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. lxx06xx & qxx06xx & qxx06xhx series 6 amp sensitive, standard & alternistor (high commutation) triacs 6.0a triacs electrical characteristics (t j = 25c, unless otherwise speci?ed) sensitive triac (4 quadrants) symbol test conditions quadrant value unit lxx06x5 lxx06x6 lxx06x8 i gt v d = 12v r l = 60 8 i C ii C iii iv max. 5 5 5 10 10 20 ma v gt all max. 1.3 v v gd v d = v drm r l = 3.3 k 8 t j = 110c all min. 0.2 v i h i t = 100ma max. 10 10 20 ma dv/dt v d = v drm gate open t j = 100c 400v typ. 30 30 40 v/s 600v 20 20 30 (dv/dt)c (di/dt)c = 3.2 a/ms t j = 110c typ. 1 2 2 v/s t gt i g = 2 x i gt pw = 15s i t = 8.5 a(pk) typ. 3.0 3.0 3.2 s electrical characteristics (t j = 25c, unless otherwise speci?ed) standard triac symbol test conditions quadrant value unit qxx06x4 qxx06x5 i gt v d = 12v r l = 60 8 i C ii C iii iv max. typ. 25 50 50 75 ma v gt i C ii C iii max. 1.3 v v gd v d = v drm r l = 3.3 k 8 t j = 125c all min. 0.2 v i h i t = 200ma max. 50 50 ma dv/dt v d = v drm gate open t j = 125c 400v min. 120 v/s 600v 100 800v 85 v d = v drm gate open t j = 100c 1000v 100 (dv/dt)c (di/dt)c = 3.2 a/ms t j = 125c typ. 4 4 v/s t gt i g = 2 x i gt pw = 15s i t = 8.5 a(pk) typ. 3.0 3.0 s electrical characteristics (t j = 25c, unless otherwise speci?ed) alternistor triac (3 quadrants) symbol test conditions quadrant value unit qxx06xh3 qxx06xh4 i gt v d = 12v r l = 60 i C ii C iii max. 10 35 ma v gt i C ii C iii max. 1.3 v v gd v d = v drm r l = 3.3 k t j = 125c i C ii C iii min. 0.2 v i h i t = 100ma max. 15 35 ma dv/dt v d = v drm gate open t j = 125c qxx06vhy / qxx06dhy min. 400v 75 400 v/s 600v 50 300 800v 200 qxx06lhy / qxx06rhy / qxx06nhy 400v 75 450 600v 50 350 800v 250 v d = v drm gate open t j = 100c all 1000v 150 (dv/dt)c (di/dt)c = 3.2 a/ms t j = 125c min. 20 25 v/s t gt i g = 2 x i gt pw = 15s i t = 8.5 a(pk) typ. 4.0 4.0 s note: xx = voltage, x = package, y = sensitivity
64 revised: july 9, 2008 ?2008 littelfuse, inc. teccor ? brand thyristors speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. speci?cations are subject to change without notice. please refer to http://www.littelfuse.com/series/triac.html for current information. 6 amp sensitive, standard & alternistor (high commutation) triacs lxx06xx & qxx06xx & qxx06xhx series static characteristics symbol test conditions value unit v tm i tm = 11.3a t p = 380 s max. 1.60 v i drm / i rrm v drm = v rrm lxx06xy t j = 25c 400 - 600v max. 20 a t j = 110c 400 - 600v 0.5 ma qxx06xy t j = 25c 400 - 1000v 50 a t j = 125c 400 - 800v 2 ma t j = 100c 1000v 3 qxx06xhy t j = 25c 400 - 800v 10 a 1000v 20 t j = 125c 400 - 800v 3 ma t j = 100c 1000v 2 thermal resistances symbol parameter value unit r r (j-c) junction to case (ac) l/qxx06ryy / l/qxx06nyy 1.8 c/w l/qxx06lyy 3.3 l/qxx06vyy / l/qxx06dyy 3.2 r r (j-a) junction to ambient l/qxx06ryy 45 c/w l/qxx06lyy 50 l/qxx06vyy 70 note: xx = voltage, x = package, y = sensitivity, yy = type & sensitivity figure 1: de?nition of quadrants figure 2: normalized dc gate trigger current for all quadrants vs. junction temperature junction temperature (t j )- c -6 5 -40 -1 5 10 3 5 60 8 5 110 1 2 5 4.0 3.0 2.0 1.0 0.0 ratio of i gt i gt (t j = 2 5 c) note: alternistors will not operate in qiv mt2 positive (positive half cycle) mt2 negative (negative half cycle) note: alternistors will not operate in qiv mt1 mt2 + i gt ref qii mt1 i gt gate mt2 ref mt1 mt2 ref mt1 mt2 ref qi qiv qiii all polarities are referenced to mt1 ( - ) i gt gate (+) i gt - i gt gate ( - ) i gt gate (+) + -
65 ?2008 littelfuse, inc. revised: july 9, 2008 teccor ? brand thyristors speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. lxx06xx & qxx06xx & qxx06xhx series 6 amp sensitive, standard & alternistor (high commutation) triacs 6.0a triacs figure 3: normalized dc holding current vs. junction temperature figure 4: normalized dc gate trigger voltage for all quadrants vs. junction temperature junction temperature (t j )- c -6 5 -40 -1 5 10 3 5 60 8 5 110 1 2 5 4.0 3.0 2.0 1. 0 0.0 ratio of i h i h (t j = 2 5 c) junction temperature (t j )- c -6 5 -40 -1 5 10 3 5 60 8 5 110 1 2 5 4.0 3.0 2.0 1.0 0.0 ratio of i h i h (t j = 2 5 c) figure 7: maximum allowable case temperature vs. on-state current (standard triac) figure 8: maximum allowable case temperature vs. on-state current (alternistor triac) rms on-state current (i t(rms) ) - amps 7 6 5 4 3 2 1 0 130 120 110 100 90 80 70 60 maximum allowable case temperature (t c ) - c qxx06rhy qxx06nhy qxx06vhy qxx06dhy qxx06lhy current waveform: sinusoidal load: resistive or inductive conduction angle: 360 case temperature: measured as shown on dimensional drawings rms on-state current (i t(rms) ) - amps 0246810121416 0 2 4 6 8 10 12 14 16 18 average on-state power dissipation (p d(av) ) - watts current waveform: sinusoidal load: resistive or inductive conduction angle: 360 figure 5: power dissipation (typical) vs. rms on-state current figure 6: maximum allowable case temperature vs. on-state current (sensitive triac) rms on-state current (i t(rms) ) - amps 7 6 5 4 3 2 1 0 120 110 100 90 80 70 60 maximum allowable case temperature (t c ) - c lxx06vy lxx06dy lxx06ry lxx06ly current waveform: sinusoidal load: resistive or inductive conduction angle: 360 case temperature: measured as shown on dimensional drawings rms on-state current (i t(rms) ) - amps 7 6 5 4 3 2 1 0 130 120 110 100 90 80 70 60 maximum allowable case temperature (t c ) - c qxx06ly current waveform: sinusoidal load: resistive or inductive conduction angle: 360 case temperature: measured as shown on dimensional drawings qxx06ry qxx06ny
66 revised: july 9, 2008 ?2008 littelfuse, inc. teccor ? brand thyristors speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. speci?cations are subject to change without notice. please refer to http://www.littelfuse.com/series/triac.html for current information. 6 amp sensitive, standard & alternistor (high commutation) triacs lxx06xx & qxx06xx & qxx06xhx series figure 9: maximum allowable ambient temperature vs. on-state current (sensitive / standard triac) figure 10: maximum allowable ambient temperature vs. on-state current (alternistor triac) rms on-state current [i t(rms) ] - amps 120 100 80 60 40 20 maximum allowable ambient temperature (t a ) - c 2.0 1. 8 1. 6 1. 4 1. 2 1. 0 0.8 0.6 0.4 0.2 0.0 current waveform: sinusoidal load: resistive or inductive conduction angle: 360 case temperature: measured as shown on dimensional drawing qxx06lhy qxx06rhy qxx06nhy qxx06vhy rms on-state current (i t(rms) ) - amps 120 100 80 60 40 20 maximum allowable ambient temperature (t a ) - c 2.0 1.8 1.6 1. 4 1.2 1.0 0.8 0.6 0.4 0.2 0.0 qxx06ly qxx06ry qxx06ny lxx06ly lxx06ry l/qxx06vy current waveform: sinusoidal load: resistive or inductive conduction angle: 360 free air rating C no heatsink figure 11: on-state current vs. on-state voltage (typical) 1.6 1. 5 1. 4 1.3 1. 2 1.1 1.0 0.9 0.8 0.7 20 18 16 14 12 10 8 6 4 2 0 t c = 2 5 c postitive or negative instantaneous on-state voltage (v t ) - volts postitive or negative instantaneous on-state current (i t ) - amps
67 ?2008 littelfuse, inc. revised: july 9, 2008 teccor ? brand thyristors speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. lxx06xx & qxx06xx & qxx06xhx series 6 amp sensitive, standard & alternistor (high commutation) triacs 6.0a triacs surge current duration- full cycles 1 peak surge (non-repetitive) on-state current (i tsm ) - amps 1 10 100 1000 10 100 qxx06ly qxx06ry qxx06ny lxx06ly lxx06ry lxx06vy lxx06dy figure 12: surge peak on-state current vs. number of cycles (sensitive / standard triac) supply frequency: 60 hz sinusoidal load: resistive rms on-state current: [i t(rms) ]: maximum rated value at speci?ed case temperature notes: 1. gate control may be lost during and immediately following surge current interval. 2. overload may not be repeated until junction temperature has returned to steady-state rated value. surge current duration- full cycles 1 peak surge (non-repetitive) on-state current (i tsm ) - amps 1 10 100 1000 10 100 qxx06lhy qxx06rhy qxx06nhy qxx06vhy qxx06dhy figure 13: surge peak on-state current vs. number of cycles (alternistor triac) supply frequency: 60 hz sinusoidal load: resistive rms on-state current: [i t(rms) ]: maximum rated value at speci?ed case temperature notes: 1. gate control may be lost during and immediately following surge current interval. 2. overload may not be repeated until junction temperature has returned to steady-state rated value. note: xx = voltage, x = package, y = sensitivity, yy = type & sensitivity
68 revised: july 9, 2008 ?2008 littelfuse, inc. teccor ? brand thyristors speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. speci?cations are subject to change without notice. please refer to http://www.littelfuse.com/series/triac.html for current information. 6 amp sensitive, standard & alternistor (high commutation) triacs lxx06xx & qxx06xx & qxx06xhx series soldering parameters re?ow condition pb C free assembly pre heat - temperature min (t s(min) ) 150c - temperature max (t s(max) ) 200c - time (min to max) (t s ) 60 C 190 secs average ramp up rate (liquidus temp) (t l ) to peak 5c/second max t s(max) to t l - ramp-up rate 5c/second max re?ow - temperature (t l ) (liquidus) 217c - temperature (t l ) 60 C 150 seconds peak temperature (t p ) 260 +0/-5 c time within 5c of actual peak temperature (t p ) 20 C 40 seconds ramp-down rate 5c/second max time 25c to peak temperature (t p ) 8 minutes max. do not exceed 280c physical speci?cations environmental speci?cations test speci?cations and conditions ac blocking (v drm ) mil-std-750, m-1040, cond a applied peak ac voltage @ 125c for 1008 hours temperature cycling mil-std-750, m-1051, 100 cycles; -40c to +150c; 15-min dwell-time temperature/ humidity eia / jedec, jesd22-a101 1008 hours; 320v - dc: 85c; 85% rel humidity high temp storage mil-std-750, m-1031, 1008 hours; 150c low-temp storage 1008 hours; -40c thermal shock mil-std-750, m-1056 10 cycles; 0c to 100c; 5-min dwell- time at each temperature; 10 sec (max) transfer time between temperature autoclave eia / jedec, jesd22-a102 168 hours (121c at 2 atms) and 100% r/h resistance to solder heat mil-std-750 method 2031 solderability ansi/j-std-002, category 3, test a lead bend mil-std-750, m-2036 cond e terminal finish 100% matte tin-plated body material ul recognized epoxy meeting ?ammability classi?cation 94v-0 terminal material copper alloy design considerations careful selection of the correct device for the applications operating parameters and environment will go a long way toward extending the operating life of the thyristor. good design practice should limit the maximum continuous current through the main terminals to 75% of the device rating. other ways to ensure long life for a power discrete semiconductor are proper heat sinking and selection of voltage ratings for worst case conditions. overheating, overvoltage (including dv/dt), and surge currents are the main killers of semiconductors. correct mounting, soldering, and forming of the leads also help protect against component damage. time temperature t p t l t s(max) t s(min) 25 t p t l t s time to peak temperature preheat p reheat ramp-up ramp-up ramp-down r amp- do
69 ?2008 littelfuse, inc. revised: july 9, 2008 teccor ? brand thyristors speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. lxx06xx & qxx06xx & qxx06xhx series 6 amp sensitive, standard & alternistor (high commutation) triacs 6.0a triacs dimensions to-220ab (r-package) non-isolated mounting tab common with center lead dimension inches millimeters min max min max a 0.380 0.420 9.65 10.67 b 0.105 0.115 2.67 2.92 c 0.230 0.250 5.84 6.35 d 0.590 0.620 14.99 15.75 e 0.142 0.147 3.61 3.73 f 0.110 0.130 2.79 3.30 g 0.540 0.575 13.72 14.61 h 0.025 0.035 0.64 0.89 j 0.195 0.205 4.95 5.21 k 0.095 0.105 2.41 2.67 l 0.060 0.075 1.52 1.91 m 0.085 0.095 2.16 2.41 n 0.018 0.024 0.46 0.61 o 0.178 0.188 4.52 4.78 p 0.045 0.060 1.14 1.52 r 0.038 0.048 0.97 1.22 dimensions to-220ab (l-package) isolated mounting tab dimension inches millimeters min max min max a 0.380 0.420 9.65 10.67 b 0.105 0.115 2.67 2.92 c 0.230 0.250 5.84 6.35 d 0.590 0.620 14.99 15.75 e 0.142 0.147 3.61 3.73 f 0.110 0.130 2.79 3.30 g 0.540 0.575 13.72 14.61 h 0.025 0.035 0.64 0.89 j 0.195 0.205 4.95 5.21 k 0.095 0.105 2.41 2.67 l 0.060 0.075 1.52 1.91 m 0.085 0.095 2.16 2.41 n 0.018 0.024 0.46 0.61 o 0.178 0.188 4.52 4.78 p 0.045 0.060 1.14 1.52 r 0.038 0.048 0.97 1.22 k j a h g b f ? e c d l r t c measuring point area (ref.) 0.17 in 2 mt2 o p n m mt1 gate .320 8.13 . 5 26 13.36 .276 7. 0 1 k j a h g b f ? e c d l r t c measuring point mt2 mt2 o p n m mt1 .276 7. 0 1 . 5 26 13.36 .320 8.13 gate area (ref.) 0.17 in 2 notch in gate lead to id. non-isolated tab note: maximum torque to be applied to mounting tab is 8 in-lbs, (0.904 nm). note: maximum torque to be applied to mounting tab is 8 in-lbs, (0.904 nm).
70 revised: july 9, 2008 ?2008 littelfuse, inc. teccor ? brand thyristors speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. speci?cations are subject to change without notice. please refer to http://www.littelfuse.com/series/triac.html for current information. 6 amp sensitive, standard & alternistor (high commutation) triacs lxx06xx & qxx06xx & qxx06xhx series dimensions to-263ab (n-package) d 2 -pak surface mount dimensions to-251aa (v-package) v-pak through hole dimension inches millimeters min max min max a 0.040 0.050 1.02 1.27 b 0.235 0.245 5.97 6.22 c 0.350 0.375 8.89 9.53 d 0.205 0.213 5.21 5.41 e 0.255 0.265 6.48 6.73 f 0.027 0.033 0.69 0.84 g 0.087 0.093 2.21 2.36 h 0.085 0.095 2.16 2.41 i 0.176 0.184 4.47 4.67 j 0.018 0.023 0.46 0.58 k 0.038 0.044 0.97 1.12 l 0.018 0.023 0.46 0.58 dimension inches millimeters min max min max a 0.360 0.370 9.14 9.40 b 0.380 0.420 9.65 10.67 c 0.178 0.188 4.52 4.78 d 0.025 0.035 0.64 0.89 e 0.045 0.060 1.14 1.52 f 0.060 0.075 1.52 1.91 g 0.095 0.105 2.41 2.67 h 0.092 0.102 2.34 2.59 j 0.018 0.024 0.46 0.61 k 0.090 0.110 2.29 2.79 s 0.590 0.625 14.99 15.88 v 0.035 0.045 0.89 1.14 u 0.002 0.010 0.05 0.25 w 0.040 0.070 1.02 1.78 area: 0.040 in 2 t c measuring point mt2 gate mt2 mt1 g i e d a b c f j h k l 5 .28 .208 5 .34 .210 g b a w f d v s mt1 mt2 t c measuring point c e k h j u .320 8.13 .276 7. 0 1 .331 8.41 gate .460 11.68 .66 5 16.89 .260 6.60 .1 5 0 3.81 .080 2.03 .08 5 2.16 .0 55 1.40 .3 5 0 8.89 .276 7. 0 1 .276 7. 0 1 area: 0.11 in 2
71 ?2008 littelfuse, inc. revised: july 9, 2008 teccor ? brand thyristors speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. lxx06xx & qxx06xx & qxx06xhx series 6 amp sensitive, standard & alternistor (high commutation) triacs 6.0a triacs dimensions to-252aa (d-package) d-pak surface mount dimension inches millimeters min max min max a 0.040 0.050 1.02 1.27 b 0.235 0.245 5.97 6.22 c 0.106 0.113 2.69 2.87 d 0.205 0.213 5.21 5.41 e 0.255 0.265 6.48 6.73 f 0.027 0.033 0.69 0.84 g 0.087 0.093 2.21 2.36 h 0.085 0.095 2.16 2.41 i 0.176 0.184 4.47 4.67 j 0.018 0.023 0.46 0.58 k 0.038 0.044 0.97 1.12 l 0.018 0.023 0.46 0.58 m 0.000 0.004 0.00 0.10 n 0.021 0.027 0.53 0.69 o0505 gate mt2 mt2 mt1 t c measuring point g i d e a b c f 5 .28 .208 5 .34 .210 : 0.040 in 2 area m o n h j l k .118 3 .063 1.60 .071 1.80 .264 6.71 .264 6.71 .181 4.60 pad layout for to-252aa (d-package)
72 revised: july 9, 2008 ?2008 littelfuse, inc. teccor ? brand thyristors speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. speci?cations are subject to change without notice. please refer to http://www.littelfuse.com/series/triac.html for current information. 6 amp sensitive, standard & alternistor (high commutation) triacs lxx06xx & qxx06xx & qxx06xhx series product selector packing options part number voltage gate sensitivity quadrants type package 400v 600v 800v 1000v i - ii - iii iv lxx06l5 x x 5 ma 5 ma sensitive triac to-220l lxx06d5 x x 5 ma 5 ma sensitive triac to-252 d-pak lxx06r5 x x 5ma 5ma sensitive triac to-220r lxx06v5 x x 5 ma 5 ma sensitive triac to-251 v-pak lxx06l6 x x 5 ma 10 ma sensitive triac to-220l lxx06d6 x x 5 ma 10 ma sensitive triac to-252 d-pak lxx06r6 x x 5ma 10ma sensitive triac to-220r lxx06v6 x x 5 ma 10 ma sensitive triac to-251 v-pak lxx06l8 x x 10 ma 20 ma sensitive triac to-220l lxx06d8 x x 10 ma 20 ma sensitive triac to-252 d-pak lxx06r8 x x 10ma 20ma sensitive triac to-220r lxx06v8 x x 10 ma 20 ma sensitive triac to-251 v-pak qxx06vh3 x x 10 ma alternistor triac to-251 v-pak qxx06dh3 x x 10 ma alternistor triac to-252 d-pak qxx06l4 x 25 ma standard triac to-220l qxx06r4 x 25 ma standard triac to-220r qxx06n4 x 25 ma standard triac to-263 d2-pak qxx06rh3 x x 10ma alternistor triac to-220r qxx06lh4 xxxx 35 ma alternistor triac to-220l qxx06rh4 xxxx 35 ma alternistor triac to-220r qxx06vh4 xxxx 35 ma alternistor triac to-251 v-pak qxx06dh4 xxxx 35 ma alternistor triac to-252 d-pak qxx06nh4 xxxx 35 ma alternistor triac to-263 d2-pak qxx06l5 x x x 50 ma standard triac to-220l qxx06r5 x x x 50 ma standard triac to-220r qxx06n5 x x x 50 ma standard triac to-263 d2-pak part number marking weight packing mode base quantity lxx06l/ry lxx06l/ry 2.2 g bulk 500 lxx06l/rytp lxx06l/ry 2.2 g tube pack 500 lxx06dytp lxx06dy 0.3 g tube 750 lxx06dyrp lxx06dy 0.3 g embossed carrier 2500 lxx06vytp lxx06vy 0.4 g tube 750 qxx06l/ryy qxx06l/ryy 2.2 g bulk 500 qxx06l/ryytp qxx06l/ryy 2.2 g tube pack 500 qxx06nyytp qxx06nyy 1.6 g tube 500 qxx06nyyrp qxx06nyy 1.6 g embossed carrier 500 qxx06dyytp qxx06dyy 0.3 g tube 750 qxx06dyyrp qxx06dyy 0.3 g embossed carrier 2500 qxx06vyytp qxx06vyy 0.4 g tube 750 note: xx = voltage; yy = sensitivity
73 ?2008 littelfuse, inc. revised: july 9, 2008 teccor ? brand thyristors speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. lxx06xx & qxx06xx & qxx06xhx series 6 amp sensitive, standard & alternistor (high commutation) triacs 6.0a triacs 0.512 (13.0) arbor hole dia. dc dc xxxxxx dc gate mt1 / cathode mt2 / anode 0.63 (16.0) 0.157 (4.0) 0.64 (16.3) 12.99 (330.0) 0.524 (13.3) 0.315 (8.0) 0.059 dia (1.5) * * cover tape direction of feed dimensions are in inches (and millimeters). gate mt1 / cathode mt2 / anode 0.512 (13.0) arbor hole dia. 0.945 (24.0) 0.63 (16.0) 1.01 (25.7) 12.99 (330.0) 0.827 (21.0) 0.157 (4.0) direction of feed dimensions are in inches (and millimeters). * * cover tape 0.059 dia (1.5) to-252 embossed carrier reel pack (rp) speci?cations meets all eia-481-2 standards to-263 embossed carrier reel pack (rp) speci?cations meets all eia-481-2 standards
74 revised: july 9, 2008 ?2008 littelfuse, inc. teccor ? brand thyristors speci?cations are subject to change without notice. please refer to http://www.littelfuse.com for current information. speci?cations are subject to change without notice. please refer to http://www.littelfuse.com/series/triac.html for current information. 6 amp sensitive, standard & alternistor (high commutation) triacs lxx06xx & qxx06xx & qxx06xhx series part numbering system part marking system current 06: 6a sensitivity & type sensitive triac: 3 : 3 ma (qi, ii, iii, iv) 5 : 5 ma (qi, ii, iii, iv) 6 : 5 ma (qi, ii, iii) 10 ma (qiv) 8 : 10 ma (qi, ii, iii) 20 ma (qiv) standard triac: 4 : 2 5 ma (qi, ii, iii) 5 : 5 0 ma (qi, ii, iii) alternistor triac: h3 : 10 ma (qi, ii, iii) h 4 : 3 5 ma (qi, ii, iii) package type l : to-220 isolated r : to-220 non-isolated n : to-263 (d 2 pak) v : to-2 5 1 (vpak) d : to-2 5 2 (dpak) voltage rating 4 0 : 400v 60 : 600v 80 : 800v k0 : 1000v lead form dimensions xx : lead form option q 60 06 l h 4 5 6 device type l : sensitive triac q : triac or alternistor ? l6006v 5 yxxxx to-2 5 2aa C (d package) to-2 5 1aa C (v package) ?

▲Up To Search▲

Price & Availability of LK006R656

	To Download LK006R656 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .